Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
This post listed below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is indeed compelling. You should check it out.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the task can move quickly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have certified yourself for the job as well as fit trying it. Rather than employing a professional to take over a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will certainly aid you install a new bathtub in your restroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water pipelines.
Your tools and material checklist should comprise the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the level reads level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water and inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill the tub as well as also check the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, causing issues with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our excerpt about Installing A Bathtub. Thank you so much for finding the time to read through our article. Do you know about someone else who is serious about the topic? Please feel free to promote it. We truly appreciate reading our article about How to Install a Bathtub.
Schedule Your Job Now
Report this page